Splošna orodja Kotomer št. 17 s pravokotno glavo iz nerjavečega jekla - merilno orodje za mizarje in ljubitelje obdelave lesa Iskalnik kotov s kvadratno glavo

Name: Splošna orodja Kotomer št. 17 s pravokotno glavo iz nerjavečega jekla - merilno orodje za mizarje in ljubitelje obdelave lesa Iskalnik kotov s kvadratno glavo
Brand: General Tools
SKU: 043985291384
Price: 39.87 EUR
Availability: InStock

Brand:General Tools

3.4/5

€
39.87

Za vse mizarske domače mojstre vas bo kvadratna glava iz nerjavečega jekla General Tools Angle Protractor vodila pri iskanju kotnih točk za vsak dom, šolo ali službo. Najprej boste želeli zrahljati matico na sredini roke kotomera. Kvadratno glavo postavite na eno stran kota, matica kotomerja pa mora biti na kotni točki. Nato boste roko naslonili na drugo nogo mesta, ki ga merite. Nato privijte matico na sredini kraka in odčitajte meritev kota na glavi ravnila. Ko gre za reze pod kotom, se je pametno držati starega reka Dvakrat meri, enkrat reži. To orodje za niveliranje vam lahko pomaga natančno izmeriti kote. Pri General Tools ponujamo več kot 1000 izdelkov, med katerimi lahko izbirate. Ponosni smo, da lahko trgovcem, rokodelcem in domačim mojstrom po vsem svetu zagotovimo široko paleto cenovno dostopnih mehanskih ročnih orodij za posebne namene ter natančnih merilnih in pregledovalnih naprav.

Znesek

Dodaj v voziček Kupi zdaj

EAN: 043985291384

kategorije Orodja in pripomočki za dom, Orodja za merjenje in načrtovanje, Protraktorji,

SPLOŠNA ORODJA: Smo priznano vodilno podjetje pri oblikovanju in razvoju specializiranih natančnih orodij, namenjenih zagotavljanju izjemnih storitev za stranke. Spodbujamo obrtnike in domače mojstre, da delajo pametneje, merijo bolje in popravljajo bolj produktivno. MERILNA ORODJA: Možnosti projektiranja so neskončne z uporabo našega visokokakovostnega kotomera s pravokotno glavo. Obvladate lahko umetnost gradnje novih omar, miz, stolov, lesenih pisalnih miz, okvirjev in različnih izdelkov pohištva. ISKALO KOTOV: Hitro in preprosto določite svoje kote z našim proti rji odpornim merilnim kompasom. Kovinska roka se zaskoči z narebričeno matico, kar vam omogoča natančno merjenje naklona. GRADBENIŠKI KOTERJI: Ta kotomer s kvadratno glavo ima polkrožno lestvico od 0 do 180 stopinj v smeri naprej in obratno za merjenje vseh kotov pri delu. Glava 3-3/8 x 2 pomaga zasidrati kotomer ob predmete, da ga drži na mestu. ROKA KOMETA: Izdelan je iz vzdržljivega nerjavečega jekla in ima 6 nastavljivo roko za nastavitev poševnega roba, prenos kotov in iskanje vaše mere. Je nepogrešljivo orodje in ideja za darilo za kolego mizarja, študenta ali strojnika.

Batteries Included?	‎No
Batteries Required?	‎No
Brand	General Tools
Color	Stainless Steel
Color	‎Stainless Steel
Country of Origin	‎Taiwan
Customer Reviews	4.4 4.4 out of 5 stars 5,269 ratings 4.4 out of 5 stars
Domestic Shipping	Item can be shipped within U.S.
Included Components	‎STEEL PROTRACTOR
International Shipping	This item can be shipped to select countries outside of the U.S. Learn More
Is Discontinued By Manufacturer	‎No
Item model number	‎17
Item Package Quantity	‎1
Item Weight	‎2.24 ounces
Manufacturer	‎General Tools
Material	Stainless Steel
Material	‎Stainless Steel
Number Of Pieces	‎1
Part Number	‎17
Pattern	‎Angle Finder
Power Source	‎Hand Powered
Product Dimensions	‎12.5 x 3.88 x 1.63 inches
Size	‎Pack of 1
Style	Square Head
Style	‎Square Head
Warranty Description	‎Manufacturer

5 Star

4 Star

3 Star

2 Star

1 Star

Napišite svojo oceno

Vaš email ne bo objavljen. Vsa obvezna polja so označena z^*

Vaša ocena

Scritto da: David

High quality

And it does what you need it to do. Worth the extra few bucks for precision

Scritto da: Amazon Customer

Angle finder

Angle finderVery easy to use very helpful tool

Scritto da: Erik Nasworthy

Decent

Not a bad product but if I had to do again I would invest in a higher quality one. Worked ok but a little flimsy. And doesn’t hold position the greatest. Ok for novice use

Scritto da: Billy Jones

Very good

Good quality

Scritto da: Rick Snyder

the service is excellent

everything!

Scritto da: T. Reich

First one was a dud - replacement is accurate! Check against a square upon receipt!

I ordered one of these to keep around the shop and the first one arrived with an inaccurate scale off by about 1 degree, reading 89 degrees when checked against a verified-accurate machinist's square. MAKE SURE YOU CHECK YOUR GAUGE AGAINST A MACHINIST SQUARE BEFORE USING IT FOR ANYTHING. Obviously when you're using this to transfer angles for replication or to create the inverse of an angle, where you won't be actually measuring the angle and are just using it as a transfer tool, then this becomes a non-issue but when using it to actually measure an angle it's frustrating. Needless to say, that unit gets one star. However I decided to give the manufacturer/Amazon another shot before leaving my review, and I contacted Amazon about the issue and a replacement was sent immediately, arriving 2 days later. They didn't request the original back so that one can still be used for just transferring angles, and I handed it off to a co-worker with the warning about the scale so he can use it for a transfer tool. The replacement is accurate! Note that this isn't a "precision scale," as the marking for reading the angle is itself is about 0.5mm wide and that presents wiggle-room in the potential for mis-reading the scale very slightly, but it gets you in the ballpark, and on the replacement it actually lands on 90 when measured against a machinist's square. It's a solid little tool, and very simple. Provided that the scale is marked accurately, there's really not much that can go wrong with this tool aside from being crushed/bent/destroyed through negligence or accident. It is low-tech and perfect for work where "good enough" certainly is; I'd advise against using it to design a space shuttle or something where the difference between 45 and 44 degrees might be a life-or-death situation, though I don't suspect folks doing such things are looking to pinch pennies on angle gauges. It was a bummer that the first one's scale wasn't precise but given how quickly and easily the issue was rectified with absolutely no fuss, I don't feel I can exactly fault the item for that sour first experience. I'd say that if you're in the market for an item like this and trying to keep the cost down, go ahead and take a shot if you're buying from a company that's easy-breezy with returns/replacements: in my experience, if you catch any accuracy issues quickly Amazon and/or General Tools will take good care of you.

Scritto da: Amazon Customer

Some fuzziness in the cursor, and the locking bolt doesn't get tight enough.

The gauge is fine for 90% of uses, but trying to dial into a specific angle is virtually impossible due to the width of the cursor and the protractor marks. It'd also be nice for the entire assembly to be thicker so it's easier to reference the straight edges, as right now it can be a bit of a balancing act. The locking nut is also pretty loose. From the factory, the washer that aides in the locking was also installed incorrectly (the notch was rotated 90 degrees in the wrong way) which prevented it from locking at all - even after fixing that, it only gets a little tight, which means it only takes a small amount of force to knock it off the angle you set it at. My recommendation if you get this: use this to find an angle and use it to set a T-bevel or another angle gauge, and reference the rest of your measurements off of that. This isn't reliable or accurate enough to be the primary reference in a project.

Scritto da: R. Brewster

a bit confusing on how to read, but helpful for estimations

im still trying to learn how the numbers work, but its small, cheap, and fits in my portable toolbox for getting a rough estimate

Scritto da: Susazz

A little smaller than expected

Fine, but it is a little smaller than I expected. It is a good thing I have good eyesight.

Scritto da: Amazon Customer

smaller than i thought

the item when arrive was a bit deceptive as I thought it would have been bigger when you see it advertised

Scritto da: Redditch

General Tools 29 plastic Protractor (angle finder)

For the price you can't complain, it's plastic, and not really designed for using in metal fabrication, being more suited to the classroom for schoolkids or college students. But, it does the job and when it breaks, cheap enough to replace

Scritto da: Shopper42

Bit flimsy, you will never get a templated angle ...

Bit flimsy, you will never get a templated angle, but my company has now bought a load instead of the hyper accurate but oversize previous units.

Scritto da: Belly

Crap

Small cheap an nasty. Product quality is like something from a Christmas cracker do not buy