Rezalna plošča Dremel 420, premer 15/16 (23,8 mm), debelina diska 0,40” (1,0 mm), pribor za rezalno rotacijsko orodje (20 kosov), srebrna

Brand:Dremel

3.7/5

€
25.98

OPIS IZDELKA Kar najbolje izkoristite svoja rotacijska orodja Dremel z uporabo naše inovativne in obsežne linije rotacijskih dodatkov in nastavkov. Ne glede na vaš projekt imamo popolno rešitev za vas. Dodatki Dremel se prilegajo vašemu rotacijskemu orodju in tako razširijo njegovo vsestranskost. Ne glede na to, ali želite rezljati, gravirati, rezati, brusiti ali brusiti, je na voljo pripomoček Dremel, s katerim lahko delo opravite z vrhunsko natančnostjo. Zato vam naši namensko izdelani dodatki Dremel omogočajo, da svoj projekt pripravite do zadnje podrobnosti. Dodatki Dremel so tudi barvno kodirani v kategorije uporabe, da vam olajšajo izbiro pravega dodatka za vaš projekt. Spremenite svoje rotacijsko orodje Dremel v rezalni stroj s 420 Dremel Cut-Off Wheels. Dobro za rezanje, ravne reze in zareze v vseh vrstah kovin, kot so kaljeno jeklo, pločevina ali aluminij. Rezalna kolesa imajo 15/16 In. (23,8 mm) premera kolesa in 0,04 In. (1,0 mm) debelo rezilo, zaradi česar je idealno za rezanje, žlebljenje in obrezovanje različnih kovin, tankega lesa ali plastike; lahko se uporablja tudi za izdelavo rež v zarjavelih ali oguljenih sornikih in vijakih. Samo za uporabo s trnom 402. Paket 20 koles. Združljivo z vsemi žičnimi in brezžičnimi rotacijskimi orodji Dremel. Ni potrebe po iskanju ustreznega vpenjalnega obroča, vsi rotacijski dodatki Dremel imajo standardno steblo 1/8". AMAZON.COM 15/16-palčna rezalna plošča Dremel Heavy Duty Cut-Off Wheel je idealna za rezanje, žlebljenje in obrezovanje vseh vrst kovin. Uporablja se lahko tudi na drugih materialih, vključno s tankim lesom, plastiko in keramiko. Ta rezalna plošča je izdelana iz trdega abraziva, ki se uporablja za rezanje in rezanje kovin, vključno s kaljenim jeklom. To kolo olajša rezanje sornikov in vijakov ter izdelavo rež v zarjavele ali oluščene sornike in vijake za odstranitev z izvijačem. To 1/2-palčno debelo polirno kolo je na voljo v paketu po 20 kosov.

Ni enot na voljo

EAN: 640026953777

kategorije Orodja in pripomočki za dom, Močno in ročno orodje, Dele in pribor za električno orodje, deli in pribor za električna rotacijska orodja, Razrezalna kolesa,

Za uporabo z rotacijskimi orodji, ki lahko sprejmejo velikost stebla 1/8. Rezalna plošča reže samo po robu. Z njimi ne poskušajte brusiti ali rezati ukrivljenih lukenj. Idealen za rezanje sornikov, vijakov, pločevine in tankega lesa. Spremenite svoje rotacijsko orodje v rezalni stroj.

Assembled Diameter	23.8 Millimeters
Assembled Diameter	‎23.8 Millimeters
Batteries Included?	‎No
Batteries Required?	‎No
Brand	Dremel
Color	‎Silver
Construction Type	Cut-off Wheels
Country of Origin	‎China
Customer Reviews	4.6 4.6 out of 5 stars 1,212 ratings 4.6 out of 5 stars
Cutting Diameter	‎23.8 Millimeters
Grit Number	180
Grit Rating	‎180
Is Discontinued By Manufacturer	‎No
Item model number	‎420
Item Package Quantity	‎20
Item Weight	‎0.192 ounces
Manufacturer	‎Dremel
Material	‎hard abrasive material
National Stock Number	‎3460-01-275-4363
Part Number	‎420
Product Dimensions	0.94"L x 0.94"W
Warranty Description	‎No

5 Star

4 Star

3 Star

2 Star

1 Star

Napišite svojo oceno

Vaš email ne bo objavljen. Vsa obvezna polja so označena z^*

Vaša ocena

Scritto da: Donald Scheer

Most Used Dremel Item I Use!

I Use These Often! So I Need A Lot Of Them! They Do A Great Job! Like All Cut-off Wheels They Wear Out Or Break! But, They Arer A Great Prodsuct.

Scritto da: Brian K Johnson

Cut of discs

These cut off discs work fine but they are not strong, they break fairly easily, but they are very inexpensive so they are still useful.

Scritto da: Rich

Did what it supposed to do.

Durable and holds to cut metal. Better than snapped on Dremel wheel. Highly recommended.

Scritto da: Whale

When you are tired of breaking cuttoff wheels, get this

Cut off tools are for cutting shafts that are usually hard steel and not so thick. But when the going gets rough and you need to cut aluminum pieces that are soft and explode your nice think blades, this is the one you need. It will deal with a lot more lateral side loads and can remove material besides just cut a slot. If I need a cut in a hardened piece of steel, the then thin cutoff tools work. But if i need to cut out a piece from an aluminum sheet or maybe remove some excess aluminum weld material, the thicker cut off wheel will last much longer although they may still explode if you force the issue. I use both cutoff tools and use the one that will survive. Usually the thicker one.

Scritto da: Nana and Pa

Excellent product

Working very well on hard steel material. Very pleased with quality of the wheels.

Scritto da: @4x4Erik

Awesome blades

These are an absolute a must have for me. I always have a supply of them. I will say, these seem to be a more coarse grit than the wheels I've had in the past, but that can also be a good thing. They last as good as any, and have worked for me.

Scritto da: David

Cut well

They work well but they are fragile. That’s why I bought so many.

Scritto da: Morse Wheeler

Dremel quality is just better than everything else

I've tried several other brands of less expensive cut-off wheels, but they have all been garbage and most lasted no more than a couple of seconds before disintegrating. Dremel wheels are just so much better...end of story. They are much thicker than the knock-offs, and unless you bind them in the workpiece, almost always wear all the way down as they should. The Dremel wheels are definitely in the category of "you get what you pay for".

Scritto da: J Le G

Great for my purposes.

Excellent for small jobs on the appropriate materials.

Scritto da: Amazon Customer

Exactly as described

I use these during my radio controlled aircraft building.

Scritto da: Steve Randall

Five Stars

Arrived safe

Scritto da: Frédéric J.

Very good "all-around" Cutting Wheel

Actually they're similar to those which came with my Dremel kit (I had only two, so I needed a refill of those "all-around" wheels). And I luv'em! I'm currently moding PC chassis, and they are perfect for : 1- Cutting through plastic, like butter. For instance I used it on an NZXT RGB LED Controler 5.25" plastic enclosure, as well as a SlimODD + 2x2.5"SSD/SSHD 5.25" bay adapter, cutting holes and redesigning edges on the sides so that I could run SATA, USB and Power wires "through" the bay controllers cage, leaving room for a Swiftech 280mm radiator plus its pump on the front lower side of the radiator (thus very tight to the bay cage). Their diameter is not too big, enough for that scale of craftsmanship. 2- Cutting curves on metal sheets. I'm using it while moding a Fractal Refine R4 PC chassis, for accommodating a 280mm CPU water cooler's radiator on the top panel ("opening" 27mm towards the left side panel: new "air vents" and mounting holes for 2x140mm fans - this mod clears the obstruction the motherboard's Power regulators Heat sinks had with the original chassis mounting holes vertical alignments - and which disallowed any 280mm radiators on the top panel). One of their "con", is also a "pro": they degrade relatively fast. I can thus use them for cutting curves, i.e. for rounding corners on steel (or aluminum) sheets, or for cutting out patterns/works of arts, their smaller radius giving more flexibility on curved lines. For straight lines or large arcs I prefer the Dremel 426 Fiberglass Reinforced, which have a bigger radius (1 1/4") for straighter cuts. I'd like to find 1 1/2 inch though, as I don't know if going with a "non-standard" proprietary mounting system like the EZ Lock (for which there's an offer of 1 1/2" cut-off Wheels), is really worth the investment...

Scritto da: Ray A

Not as heavy duty as one might expect.

Even though these disks are sold as heavy duty, take it with a grain of salt. Unless you are very careful when cutting material the disks will break and pieces of shrapnel will fly, so make sure you wear protective glasses to save your eyes!.